-
1 pallet buffer position
Автоматика: дополнительная позиция для спутникаУниверсальный англо-русский словарь > pallet buffer position
-
2 pallet buffer position
English-Russian dictionary of mechanical engineering and automation > pallet buffer position
-
3 position
1) позиция; положение, заданное положение; координата || устанавливать в положение, устанавливать в заданное положение, позиционировать2) расположение•at a specified position — в заданной позиции; в заданном положении
to bring into an active position — выводить в рабочую позицию, выводить в рабочее положение
to position down — перемещать вниз, перемещаться вниз
to hold the position — сохранять положение, сохранять заданное положение
to manually position — позиционировать вручную; устанавливать вручную
- on positionto position up — перемещать вверх, перемещаться вверх
- out position
- absolute ordinate slide position
- active position
- actual position
- actuated position
- advanced position
- angular position
- article-capturing position
- at-rest position
- axial position
- best running position
- bevel position
- blank position
- broach position
- broaching position
- buffer position
- carousel positions
- Cartesian positions
- center position
- check position
- clearance position
- closed position
- command position
- commanded drive position
- commanded position
- continuous path position
- coordinate position
- cradle position
- cut-off position
- cutter axial position
- cutting position
- datum position
- dead center position
- defined position
- demand position
- desired load/unload position
- desired position
- disengaging position
- docking position
- down position
- downhand position
- downwardmost position
- dressing position
- dwell position
- dynamic position
- end position
- equally-spaced positions
- equilibrium position
- exchange position
- extreme position
- farthest position
- farthest withdrawn position
- feed position
- fetch position
- final position
- finger-closed position
- finger-open position
- first position
- flat position
- full finger-open position
- full retract position
- full-open position
- fully retracted position
- gaging position
- grasping position
- gravity position
- grind position
- grinding position
- grinding wheel datum position
- gripping position
- home position
- inactive position
- indexed position
- initial position
- initial setup position
- innermost position
- inoperative position
- input position
- instantaneous position
- jaw-loading position
- joint position
- lattice position
- levitating position
- lifted-up position
- lift-off position
- live-tool position
- load/unload position
- locked position
- locking position
- lower position
- lowered position
- lowermost position
- machine tool reference position
- machining position
- manual-off position
- manual-on position
- meshing position
- mid position
- mid-point position
- mid-travel position
- miter position
- neutral position
- nonoperating position
- offset position
- open position
- operating position
- operation-terminating position
- operative position
- operator position
- origin position
- outermost position
- out-of-reach position
- out-of-the way position
- out-of-tolerance position
- output position
- overhead position
- pallet buffer position
- pallet position
- pallet stand position
- pallet storage position
- pallet-loading position
- park position
- parked position
- part interchange position
- part pickup position
- peak-damage position
- pick-up position
- position of load application
- position of minimum out-of-true running
- position of rest
- positive position
- preadjusted cutting position
- prearranged position
- predetermined position
- prepulse position
- prescribed position
- preset position
- previous tool change position
- programmed approach position
- raised position
- ready position
- ready-to-change position
- ready-to-replace position
- ready-to-work position
- reference position
- reference target position
- referenced position
- registered position
- regulating unit position
- relative position
- release position
- reset position
- rest position
- retracted position
- retrieval position
- ring stable position
- robot pick-up position
- robot's position
- rotary tooling position
- rotational position
- running position
- runout position
- safe position
- scanning position
- service position
- setpoint position
- shaft position
- sloping position
- stable equilibrium position
- stall position
- standard position
- standby position
- start position
- static tooling position
- stop position
- storage position
- subreference position
- target levitating position
- target position
- task position
- tilted position
- tool change position
- tool home position
- tool tip position
- tool-gripping position
- tooling buffer position
- tool-loading position
- tool-releasing position
- tool's position
- true position of axis
- true position
- TSS null position
- unknown position
- unlocked position
- unlocking position
- up position
- updated position
- uppermost position
- upwardmost position
- valve position
- waiting position
- weld position
- welding position
- work loading/unloading position
- working position
- workpiece grinding position
- workpiece-loading position
- Z-axis return position
- zero positionEnglish-Russian dictionary of mechanical engineering and automation > position
См. также в других словарях:
G-code — G Code, or preparatory code or function, are functions in the Numerical control programming language. The G codes are the codes that position the tool and do the actual work, as opposed to M codes, that manages the machine; T for tool related… … Wikipedia
Radio-frequency identification — (RFID) is a technology that uses radio waves to transfer data from an electronic tag, called RFID tag or label, attached to an object, through a reader for the purpose of identifying and tracking the object. Some RFID tags can be read from… … Wikipedia
Milling machine — For the machine used in road construction, see Asphalt milling machine. Not to be confused with mill (grinding). Example of a bridge type CNC vertical milling center … Wikipedia
Check weigher — Example checkweigher. Product passes on the conveyor belt where it is weighed A checkweigher is an automatic machine for checking the weight of packaged commodities. It is normally found at the offgoing end of a production process and is used to… … Wikipedia
Lathe (metal) — Center lathe with DRO and chuck guard. Size is 460 mm swing x 1000 mm between centers A metal lathe or metalworking lathe is a large class of lathes designed for precisely machining relatively hard materials. They were originally designed to… … Wikipedia
